化学改性氧化石墨烯交联的聚酰亚胺气凝胶

doi:10.3866/PKU.WHXB201504146

物理化学学报 >> 2015, Vol. 31 >> Issue (6): 1179-1185.doi: 10.3866/PKU.WHXB201504146

化学改性氧化石墨烯交联的聚酰亚胺气凝胶

梁祎, 卢赟, 姚维尚, 张学同

北京理工大学材料科学与工程学院, 北京100081

收稿日期:2014-12-30 修回日期:2015-04-13 发布日期:2015-06-05
通讯作者: 卢赟, 张学同 E-mail:luyun@bit.edu.cn;zhangxtchina@yahoo.com
基金资助:
国家自然科学基金(21373024)和北京理工大学创新项目基金资助

Polyimide Aerogels Crosslinked with Chemically Modified Graphene Oxide

LIANG Yi, LU Yun, YAO Wei-Shang, ZHANG Xue-Tong

School of Materials Science & Engineering, Beijing Institute of Technology, Beijing 100081, P. R. China

Received:2014-12-30 Revised:2015-04-13 Published:2015-06-05
Contact: LU Yun, ZHANG Xue-Tong E-mail:luyun@bit.edu.cn;zhangxtchina@yahoo.com
Supported by:
The project was supported by the National Natural Science Foundation of China (21373024) and Innovation Program of the Beijing Institute of Technology, China.

摘要/Abstract

摘要：

聚酰亚胺(PI)气凝胶是一类密度低、机械性能好、隔热性能优异的多孔材料, 通常使用昂贵的化学交联剂进行交联. 氧化石墨烯(GO)是近年来广受关注的用于聚合物增强的纳米功能填料. 以前报道的PI/GO 复合材料多是纤维或膜的形式. 为了获得PI/GO 复合气凝胶, 本文采用化学改性氧化石墨烯(m-GO)替代1,3,5-三(4-氨基苯氧基)苯(TAB)等常规的交联剂, 使之与4,4'-二氨基二苯基醚(ODA)和3,3',4,4'-联苯四羧酸二酐(BPDA)反应, 制得了m-GO交联的PI 气凝胶. GO的化学改性通过其与过量ODA在水热条件下反应实现. 通过扫描电子显微镜(SEM)研究了PI/m-GO气凝胶的微观结构. 分别通过氮气吸脱附测试、热重分析和热线法研究了m-GO对气凝胶的孔特性、热稳定性和热导率的影响. 测试结果表明, 所获得的PI/m-GO气凝胶保持了高的孔隙率、热稳定性和绝热性. 压缩测试结果显示, 与采用1.8% (质量分数, w)的TAB进行交联的PI 气凝胶相比,仅用0.6% (w)的m-GO交联所获得的气凝胶具有更高的比杨氏模量(杨氏模量/密度)、比屈服强度(屈服强度/密度)和更小的体积收缩率.

关键词: 聚酰亚胺气凝胶, 氧化石墨烯, 交联, 机械性能, 收缩率

Abstract:

Polyimide (PI) aerogels, which are generally crosslinked using expensive chemical crosslinking agents, are novel porous materials with high strength, high heat resistance, high porosity, and low density. Graphene oxide (GO) is a functional nanofiller that has aroused wide interest in recent years. The reported PI/ GO composites have mostly been in the form of fibers and films. In this study, PI/GO composite aerogels were obtained using chemically modified graphene oxide (m-GO) as the crosslinking agent, instead of traditional ones such as 1,3,5-triaminophenoxybenzene (TAB), by reaction with 4,4'-oxydianiline (ODA) and 3,3',4,4'- biphenyltetracarboxylic dianhydride (BPDA). The chemical modification of GO was achieved by reacting GO with excess ODA using a hydrothermal method. The microstructures of the PI/m-GO aerogels were investigated using scanning electron microscopy (SEM). Nitrogen sorption tests, thermogravimetric analysis, and a hot-wire method were used to investigate the effects of m-GO on the pore properties, thermal stabilities, and thermal conductivities, respectively, of the resulting aerogels. The results show that the PI/m-GO aerogels are highly porous, thermally stable, and heat insulating. Compression tests showed that the PI aerogel prepared using 0.6% (mass fraction, w) m-GO instead of 1.8% (w) TAB as the crosslinking agent had a higher specific Young's modulus [Young's modulus/density (ρ)] and specific yield strength (yield strength/ρ), and less shrinkage.

Key words: Polyimide aerogel, Graphene oxide, Crosslinking, Mechanical property, Shrinkage ratio

点击下载补充材料PDF格式文件

梁祎, 卢赟, 姚维尚, 张学同. 化学改性氧化石墨烯交联的聚酰亚胺气凝胶[J]. 物理化学学报, 2015, 31(6), 1179-1185. doi: 10.3866/PKU.WHXB201504146

LIANG Yi, LU Yun, YAO Wei-Shang, ZHANG Xue-Tong. Polyimide Aerogels Crosslinked with Chemically Modified Graphene Oxide[J]. Acta Phys. -Chim. Sin. 2015, 31(6), 1179-1185. doi: 10.3866/PKU.WHXB201504146

链接本文: https://www.whxb.pku.edu.cn/CN/10.3866/PKU.WHXB201504146

https://www.whxb.pku.edu.cn/CN/Y2015/V31/I6/1179

参考文献

(1) Kistler, S. S. Nature 1931, 127, 741.
(2) Tamon, H.; Ishizaka, H.; Mikami, M.; Okazaki, M. Carbon 1997, 35 (6), 791. doi: 10.1016/S0008-6223(97)00024-9
(3) Wang, Z.; Dai, Z.; Wu, J.; Zhao, N.; Xu, J. Adv. Mater. 2013, 25 (32), 4494. doi: 10.1002/adma.v25.32
(4) Xu, Z. J.; Ji, T.; Zhao, L.; Wang, W. Y.; Yang, C. Y.; Gan, L. H. Acta Phys. -Chim. Sin. 2012, 28 (2), 361. [徐子颉, 吉涛, 赵蕾, 王玮衍, 杨春艳, 甘礼华. 物理化学学报, 2012, 28 (2), 361.] doi: 10.3866/PKU.WHXB201112063
(5) Guo, X. Z.; Yan, L. Q.; Yang, H.; Li, J.; Li, C. Y.; Cai, X. B. Acta Phys. -Chim. Sin. 2011, 27 (10), 2478. [郭兴忠, 颜立清, 杨辉, 李建, 李超宇, 蔡晓波. 物理化学学报, 2011, 27 (10), 2478.] doi: 10.3866/PKU.WHXB20110925
(6) Xu, W.W.; Du, A.; Tang, J.; Chen, K.; Zou, L. P.; Zhang, Z. H.; Shen, J.; Zhou, B. Acta Phys. -Chim. Sin. 2012, 28 (12), 2958. [许维维, 杜艾, 唐俊, 陈珂, 邹丽萍, 张志华, 沈军, 周斌. 物理化学学报, 2012, 28 (12), 2958.] doi: 10.3866/PKU.WHXB201209282
(7) Rhine, W.; Wang, J.; Begag, R. Production of Polyimide Aerogel for Carbon Aerogel, Involves Contacting Diamine and Aromatic Dianhydride Monomers in Solvent, Contacting Resulting Poly(amic acid) with Dehydrating Agent, and Drying Resulting Polyimide Gel. U. S. Patent 2004/0132845 A1, 2004-07-08.
(8) Guo, H.; Meador, M. A. B.; McCorkle, L.; Quade, D. J.; Guo, J.; Hamilton, B.; Cakmak, M.; Sprowl, G. ACS Appl. Mater. Interfaces 2011, 3 (2), 546. doi: 10.1021/am101123h
(9) Guo, H.; Meador, M. A. B.; McCorkle, L.; Quade, D. J.; Guo, J.; Hamilton, B.; Cakmak, M. ACS Appl. Mater. Interfaces 2012, 4
(10), 5422. doi: 10.1021/am301347a
(10) Meador, M. A. B.; Malow, E. J.; Silva, R.; Wright, S.; Quade, D.; Vivod, S. L.; Guo, H.; Guo, J.; Cakmak, M. ACS Appl. Mater. Interfaces 2012, 4 (2), 536. doi: 10.1021/am2014635
(11) Meador, M. A. B.; Wright, S.; Sandberq, A.; Nquyen, B. N.; Vankeuls, F.W.; Mueller, C. H.; Rodríguez-Solís, R.; Miranda, F. A. ACS Appl. Mater. Interfaces 2012, 4 (11), 6346. doi: 10.1021/am301985s
(12) Novoselov, K. S.; Jiang, D.; Schedin, F.; Booth, T. J.; Khotkevich, V. V.; Morozov, S. V.; Geim, A. K. Proceedings of the National Academy of Sciences 2005, 102 (30), 10451. doi: 10.1073/pnas.0502848102
(13) Mkhoyan, K. A.; Contryman, A.W.; Silcox, J.; Stewart, D. A.; Eda, G.; Mattevi, C.; Miller, S.; Chhowalla, M. Nano Lett. 2009, 9 (3), 1058. doi: 10.1021/nl8034256
(14) Shi, H.; Li, Y.; Guo, T. J. Appl. Polym. Sci. 2013, 128 (5), 3163. doi: 10.1002/app.v128.5
(15) Dong, J.; Yin, C.; Zhao, X.; Li, Y.; Zhang, Q. Polymer 2013, 54 (23), 6415. doi: 10.1016/j.polymer.2013.09.035
(16) Huang, T.; Xin, Y. S.; Li, T. S.; Nutt, S.; Su, C.; Chen, H. M.; Liu, P.; Lai, Z. L. ACS Appl. Mater. Interfaces 2013, 5 (11), 4878. doi: 10.1021/am400635x
(17) Park, O. K.; Hwang, J. Y.; Goh, M.; Lee, J. H.; Ku, B. C.; You, N. H. Macromolecules 2013, 46 (9), 3505. doi: 10.1021/ma400185j
(18) Liao, W. H.; Yang, S. Y.; Wang, J. Y.; Tien, H.W.; Hsiao, S. T.; Wang, Y. S.; Li, S. M.; Ma, C. C. M.; Wu, Y. F. ACS Appl. Mater. Interfaces 2013, 5 (3), 869. doi: 10.1021/am302494c
(19) Yoonessi, M.; Shi, Y.; Scheiman, D. A.; Lebron-Colon, M.; Tigelaar, D. M.; Weiss, R. A.; Meador, M. A. ACS Nano 2012, 6 (9), 7644.
(20) Zhang, X.; Sui, Z.; Xu, B.; Yue, S.; Luo, Y.; Zhan, W.; Liu, B. J. Mater. Chem. 2011, 21 (18), 6494. doi: 10.1039/c1jm10239g
(21) Ghani, M. A. A.; Abdallah, D.; Kazmaier, P. M.; Keoshkerian, B.; Buncel, E. Can. J. Chem. 2004, 82 (9), 1403. doi: 10.1139/v04-106
(22) Wang, G. Q. Water Resources Protection 2007, 23 (4), 85. [王国贤. 水资源保护, 2007, 23 (4), 85.]
(23) Chen, H.; Yin, J. 1, 3, 5-Tri (4-amino phenoxy) Benzene and Preparation Method Thereof. CN Patent 1405145 A, 2003-03-26. [陈焕, 印杰. 1, 3, 5-三(4-氨基苯氧基)苯及其制备方法: 中国, CN 1405145 A [P]. 2003-03-26.]
(24) Chidambareswarapattar, C.; Larimore, Z.; Sotiriou-Leventis, C.; Mang, J. T.; Leventis, N. J. Mater. Chem. 2010, 20 (43), 9666. doi: 10.1039/c0jm01844a
(25) Wu, W.; Wang, K.; Zhan, M, S. Ind. Eng. Chem. Res. 2012, 51 (39), 12821. doi: 10.1021/ie301622s
(26) Leventis, N.; Sotiriou-Leventis, C.; Mohite, D. P.; Larimore, Z. J.; Mang, J. T.; Churu, G.; Lu, H. Chem. Mate. 2011, 23 (8), 2250. doi: 10.1021/cm200323e
(27) Yang, S.; Feng, X.; Müllen, K. Adv. Mater. 2011, 23 (31), 3575. doi: 10.1002/adma.201101599

[1]	吕浩亮, 王雪杰, 杨宇, 刘涛, 张留洋. 还原氧化石墨烯包覆MOF衍生In₂Se₃用于钠离子电池负极[J]. 物理化学学报, 2023, 39(3): 2210014 -0 .
[2]	何文倩, 邸亚, 姜南, 刘遵峰, 陈永胜. 石墨烯诱导水凝胶成核的高强韧人造蛛丝[J]. 物理化学学报, 2022, 38(9): 2204059 - .
[3]	陈帅, 秦江雷, 杜建忠. 可交联且可生物降解的高分子膜[J]. 物理化学学报, 2022, 38(8): 2006029 - .
[4]	毛赫南, 王晓工. 影响高浓度氧化石墨烯分散液流变行为的重要因素及群体平衡动力学分析[J]. 物理化学学报, 2022, 38(4): 2004025 - .
[5]	樊晔, 曹崇梅, 方云, 夏咏梅. 自交联共轭亚油酸囊泡基荧光纳米点的构筑及其荧光特性[J]. 物理化学学报, 2022, 38(3): 2002032 - .
[6]	王键, 尹波, 高天, 王星懿, 李望, 洪兴星, 汪竹青, 何海勇. 还原氧化石墨烯改性少层剥离石墨增强石墨基钾离子电池负极稳定性[J]. 物理化学学报, 2022, 38(2): 2012088 - .
[7]	廖雨瑶, 范震, 杜建忠. 光交联固化的聚合物囊泡用于降温触发的药物释放[J]. 物理化学学报, 2021, 37(10): 1912053 - .
[8]	何妍,李豪,周莉,徐婷,彭昌军,刘洪来. 新型芳香三嗪超交联多孔聚合物去除水溶液中甲基橙[J]. 物理化学学报, 2019, 35(3): 299 -306 .
[9]	彭鹏,刘洪涛,武斌,汤庆鑫,刘云圻. 氮掺杂石墨烯的p型场效应及其精细调控[J]. 物理化学学报, 2019, 35(11): 1282 -1290 .
[10]	杜惟实,吕耀康,蔡志威,张诚. 基于三维多孔石墨烯/含钛共轭聚合物复合多孔薄膜的柔性全固态超级电容器[J]. 物理化学学报, 2017, 33(9): 1828 -1837 .
[11]	李一鸣,陈肖,刘晓军,李文有,贺蕴秋. 氧化石墨烯在氧化锌衬底上的电化学还原及其光电性能[J]. 物理化学学报, 2017, 33(3): 554 -562 .
[12]	曹朋飞,胡杨,张有为,彭静,翟茂林. 无定型钼硫化物/还原氧化石墨烯的辐射合成及其电催化析氢性能[J]. 物理化学学报, 2017, 33(12): 2542 -2549 .
[13]	曾向东,赵晓昱,韦会鸽,王彦飞,唐娜,沙作良. 聚苯胺-还原氧化石墨烯复合材料的比电容及超级电容性能[J]. 物理化学学报, 2017, 33(10): 2035 -2041 .
[14]	赵胜君,张伟,邓会宁,刘伟. 氧化石墨烯/聚电解质层层自组装制备单价离子选择性膜[J]. 物理化学学报, 2016, 32(3): 723 -727 .
[15]	李婷,向双飞,东为富,马丕明,施冬健,陈明清. 纳米钠基蒙脱土复合超强机械性能双网络抗菌水凝胶[J]. 物理化学学报, 2016, 32(11): 2761 -2768 .

化学改性氧化石墨烯交联的聚酰亚胺气凝胶

Polyimide Aerogels Crosslinked with Chemically Modified Graphene Oxide

PDF

赞

可视化

摘要/Abstract

支持信息

引用本文

使用本文

参考文献

相关文章 15

Metrics

推荐阅读 0